web stats
Mirth Community - Search Results

Go Back   Mirth Community > Search Forums

Showing results 1 to 25 of 500
Search took 0.01 seconds.
Search: Posts Made By: kirbykn2
Forum: Support 02-19-2019, 08:24 AM
Replies: 5
Views: 238
Posted By kirbykn2
Look at the response transformer section in the...

Look at the response transformer section in the manual or API
Forum: General Discussion 02-14-2019, 12:10 PM
Replies: 1
Views: 79
Posted By kirbykn2
yes

yes
Forum: Support 02-14-2019, 10:22 AM
Replies: 2
Views: 60
Posted By kirbykn2
What makes you think its not working? are you...

What makes you think its not working? are you getting errors?
Forum: Support 01-02-2019, 10:16 AM
Replies: 5
Views: 238
Posted By kirbykn2
Store the response to a channel map variable, and...

Store the response to a channel map variable, and create a destination to store the variable to a file.
Forum: Support 09-04-2018, 07:23 AM
Replies: 5
Views: 464
Posted By kirbykn2
What is the results of a connection test from...

What is the results of a connection test from your destination?
Forum: Support 07-13-2018, 05:40 AM
Replies: 10
Views: 1,175
Posted By kirbykn2
The connection as a constant stream of incoming...

The connection as a constant stream of incoming and outgoing requests. So I do not close the connection after each request. I don't think constantly opening and closing the connection makes sense.
Forum: Support 07-07-2018, 07:01 AM
Replies: 10
Views: 1,175
Posted By kirbykn2
I open the connection and put the the connection...

I open the connection and put the the connection to the GlobalMap. My channels then access the connection through the globalMap.
Forum: Support 07-03-2018, 09:27 AM
Replies: 3
Views: 484
Posted By kirbykn2
I would not expect to receive different encoded...

I would not expect to receive different encoded messages on the same interface.
Forum: Support 07-03-2018, 09:21 AM
Replies: 1
Views: 314
Posted By kirbykn2
Search the forum for putting to the globalMap. ...

Search the forum for putting to the globalMap. Also, there is lots of good information in the manual.
https://bridge.nextgen.com/media/3244/mirth-data-sheet-mirth-connect-3-5-user-guide.pdf
Forum: Support 07-03-2018, 09:13 AM
Replies: 8
Views: 560
Posted By kirbykn2
Also, I would use destination set filtering for...

Also, I would use destination set filtering for this.
Forum: Support 07-03-2018, 07:22 AM
Replies: 8
Views: 560
Posted By kirbykn2
Can you post a sample message. ...

Can you post a sample message.

logger.info("this is the msgType "+msgType);
Forum: Development 07-03-2018, 07:20 AM
Replies: 2
Views: 994
Posted By kirbykn2
This is part of the paid version.

This is part of the paid version.
Forum: Support 07-03-2018, 03:54 AM
Replies: 4
Views: 999
Posted By kirbykn2
Perhaps you can use the batch processor. Can you...

Perhaps you can use the batch processor. Can you provide some more detail as to what you are doing?
Forum: Support 06-26-2018, 07:18 AM
Replies: 12
Views: 444
Posted By kirbykn2
I would have the sending system fix the issue, if...

I would have the sending system fix the issue, if you can.
Forum: Support 06-26-2018, 07:14 AM
Replies: 12
Views: 444
Posted By kirbykn2
To Sid's point, take a close look at the MSH. ...

To Sid's point, take a close look at the MSH.

What is the sub-component separator for the message you are having the issue with?
Forum: Support 06-26-2018, 06:48 AM
Replies: 12
Views: 444
Posted By kirbykn2
What version of Mirth? I tested this in my...

What version of Mirth?

I tested this in my environment and it worked as expected. I copied the PID segment into this message.

Can you test with this message? Perhaps its an issue with the...
Forum: Support 06-25-2018, 09:37 AM
Replies: 4
Views: 296
Posted By kirbykn2
Don't create infinite loops. :) Killing the...

Don't create infinite loops. :)

Killing the server and removing the message stuck in a loop is what I have had to do to resolve this issue. Sometimes I believe I have been able to HALT the...
Forum: Support 06-07-2018, 11:50 AM
Replies: 2
Views: 280
Posted By kirbykn2
You might consider using an outbound message...

You might consider using an outbound message template, and only send what you want too.
Forum: Support 06-04-2018, 12:39 PM
Replies: 1
Views: 359
Posted By kirbykn2
I took the advanced course about 1 1/2 years ago....

I took the advanced course about 1 1/2 years ago. Good takeaways, good training
Forum: Support 05-22-2018, 07:18 AM
Replies: 1
Views: 259
Posted By kirbykn2
post your code.

post your code.
Forum: Support 05-17-2018, 07:56 AM
Replies: 6
Views: 486
Posted By kirbykn2
http://www.mirthproject.org/community/forums/showt...

http://www.mirthproject.org/community/forums/showthread.php?t=8136&highlight=file+lookup
Forum: Support 05-17-2018, 06:23 AM
Replies: 6
Views: 486
Posted By kirbykn2
The simplest way is a mapper step. Populate your...

The simplest way is a mapper step. Populate your translation values in the the string replacement area.
Forum: Support 05-17-2018, 06:12 AM
Replies: 6
Views: 483
Posted By kirbykn2
export the source message.

export the source message.
Forum: Support 05-17-2018, 06:09 AM
Replies: 4
Views: 780
Posted By kirbykn2
What is the message size and volume? What is the...

What is the message size and volume? What is the server configuration (memory, cpus, disk, etc)
Forum: Support 05-11-2018, 08:45 AM
Replies: 1
Views: 281
Posted By kirbykn2
You will need to increase the setID for each...

You will need to increase the setID for each appended segment.
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -8. The time now is 07:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Mirth Corporation